Module 1 - Fiat, Lancia,
Citroen, Peugeot immobox Delphi
Peugeot: Boxer(-2001) |
 |
| |
|
Module 2 - Fiat, Lancia, Maserati
IMM001.01 immobox Marelli
Memory device is Motorola MCU MC68HC05E6 SO28 package.
Expected file size is 160 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Fiat: Bravo(1998-2001), Marea(1998-), Palio(-1999)
Lancia:Dedra, Y
Maserati: GT |
 |
| |
|
Module 3 - Fiat, Lancia
IMM110.01 immobox Marelli
Memory device is Motorola MCU MC68HC908AZ32 QFP64 package.
Expected file size is 512 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Important note: if mask of Motorola is 1K59H - eeprom
area is locked (whole eeprom reads as AD AD AD...). No programmer can
read it.
Vehicles equipped with this unit:
Fiat: Bravo(1998-2001), Marea(1998-), Palio(-1999)
Lancia: Dedra, Y
Maserati: GT |
 |
| |
|
Module 4 - Alfa Romeo, Iveco
CODE1 immobox Bosch
Memory device is serial eeprom 93c46, which can be either DIL8 or SMD8 package.
Expected file size is 128
bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Fiat: Coupe, Croma
Alfa Romeo: 145, 146, 155, 164, GTV, Spider
Iveco: Daily(-2001)
Lancia: K, K coupe |
 |
| |
|
Module 5 - Alfa Romeo CODE2
immobox Bosch
Memory device is serial eeprom 93c56 SMD8 package.
Expected file size is 256 bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready programmed to start
the vehicle.
If old keys are erased, software shows PIN code and prepares transponder,
ready to be
matched with vehicle using diagnostic device.
Vehicles equipped with this unit:
Alfa Romeo: 156(1998-2001), 166(1998-2001) |
 |
| |
|
Module 6 - Fiat, Lancia, Alfa
Romeo, Maserati CODE2 with BSI Marelli
Memory device is Motorola MCU, which can be either
MC68HC912DG128 or MC9S12DG256, both QFP 112 package.
For MC68HC912DG128 expected file size is 2048 bytes,
for MC9S12DG256 file size must be 4096 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Module also shows PIN code and
transponder have to be
matched with car.
If there is not valid key, usual you have to wait
15 minutes for accepting PIN code.
Vehicles equipped with this unit:
Alfa Romeo: 147, GT
Fiat: Stilo(1999-2007), Palio(1999-)
Lancia: Thesis, Ypsilon
Maserati: Quattroporte, Granturismo |
 |
| |
|
Module 7 - Fiat, Lancia, Alfa
Romeo CODE2 with BSI Delphi
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Module also shows PIN code and
transponder have to be
matched with car.
If there is not valid key, usual you have to wait
15 minutes for accepting PIN code.
Vehicles equipped with this unit:
Fiat: Albea, Doblo, Punto(1999-), Siena, Strada |
 |
| |
|
Module 8 - Fiat, Citroen,
Peugeot CODE2 immobox Delphi
Memory device is serial eeprom 93c56 SMD8 package.
Expected file size is 256 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Module also shows PIN code and
transponder have to be
matched with car.
Vehicles equipped with this unit:
Fiat: Ducato(2001-2006), Seicento(1999-)
Citroen: Jumper(2001-2006), Relay(2001-2006)
Peugeot: Boxer(2001-2006) |
 |
| |
|
Module 9 -
Fiat, Lancia IMM100.01 immobox Marelli
Memory device is Motorola MCU MC68HC908AZ32 QFP64 package.
Expected file size is 512 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Module also shows PIN code and
transponder have to matched with car.
Important note: if mask of Motorola is 1K59H - eeprom
area is locked (whole eeprom reads as AD AD AD...). No programmer can
read it.
Vehicles equipped with this unit:
Lancia: Lybra
Fiat: Idea, Multipla |
 |
| |
|
Module 10 - Audi immobox
Delphi
Memory device is serial memory 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Audi: A4(-1997), A6(-1997) |
 |
| |
|
Module 11 -
Peugeot,Fiat,Citroen immobox Siemens
Memory device is Motorola MCU MC68HC05E6 SO28 package.
Expected file size is 160 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Peugeot: 306, Expert, Ranch
Citroen: Jumpy, Evasion
Fiat: Scudo, Ulysse |
 |
| |
|
Module 12 - Peugeot, Citroen
immobox Valeo
Memory device is serial memory 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Citroen: Saxo, Berlingo(-2000)
Peugeot: 106, 406(-1999), Partner(-2000) |
 |
| |
|
Module 13 - Peugeot, Fiat,
Lancia, Citroen CPH Texton
Memory device is serial eeprom, which can be either
93c66 or 95040, both SMD8 package.
Expected file size is 512 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Peugeot: 306, 806, Expert, Ranch
Citroen: Jumpy, Evasion, Xantia(-1999), Xsara(-1999)
Fiat: Scudo, Ulysse |
 |
| |
|
Module 14 - Peugeot 206 BSI
Siemens
Memory device is Motorola MCU MC68HC05B16 PLCC52 package.
Expected file size is 256 bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Peugeot: 206(1998-2001) |
 |
| |
|
Module 15 - Peugeot 406 BSI
Siemens
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Peugeot: 406(1999-2002) |
 |
| |
|
Module 16 - Daewoo
immobox
Memory device is Motorola MCU MC68HC05B16 PLCC52 package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Daewoo: Espero, Lanos(-2002), Leganza(-2000), Matiz(-2001), Nexia, Nubira(-2000) |
 |
| |
|
Module 17 - Honda, Rover
immobox Valeo
Memory device is Motorola MCU MC68HC05B16 PLCC52 package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Honda: Accord(-1999), Civic(-2001)
Rover: 600, 618, 620, 800 |
 |
| |
|
Module 18 - Honda, Acura
immobox Megamos
Memory device is serial memory 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Honda: Accord(-1999), Civic(-2001), CR-V(-2000), Integra, Legend, Passport, Prelude, Shuttle(-2000) |
 |
| |
|
Module 19 - Opel IMMO1 immobox
Siemens
Memory device is Motorola MCU MC68HC05B16 PLCC52 package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Opel: Astra F, Calibra, Combo B, Corsa B, Omega(1996-1999), Sintra(-1999), Tigra, Vectra B
Cadillac: Catera |
 |
| |
|
Module 20 - Opel IMMO2 immobox
Siemens
Memory device is Texas Instrument MCU TMS370C702 PLCC28 package or Motorola MCU HC908AB16A QFP64 package.
Motorola is locked, password for reading eeprom is F3-B1-F3-AB-F3-A5-F3-9F.
Expected file size is 256 bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Opel: Agila, Astra G, Combo C, Corsa C, Meriva, Omega(1999-), Sintra(1999-), Tigra, Vectra B(1999-), Zafira |
 |
| |
|
Module 21 - Mitsubishi immobox
Bosch
Memory device is serial eeprom 93c56 SMD8 package.
Expected file size is 256 bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Mitsubishi: Carisma(1998-), Space Star(1998-) |
 |
| |
|
Module 22 - VW, Skoda, Seat
IMMO1 immobox Siemens
Memory device is Motorola MCU MC68HC05B16 PLCC52 package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
VW: Caddy(-1998), Golf 3, Passat 3, Polo 3(-1998), Sharan(-1998), Transporter(-1998), Vento
Seat: Arosa(-1998), Alhambra(-1998), Cordoba(-1998), Ibiza(-1998), Inca(-1998), Toledo
Skoda: Felicia, Pick-up
Ford: Galaxy |
 |
| |
|
Module 23 - VW, Seat IMMO2
immobox Siemens
Memory device is Texas Instrument MCU TMS370C702 PLCC28 package.
Expected file size is 256 bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
VW: Caddy(1998-2000), Golf cabrio, Lupo(-2000). Polo 3(1998-2000), Sharan(1998-2000), Transporter(1998-2000)
Seat: Arosa(-2000), Cordoba Vario(-2000), Ibiza(1998-2000), Inca(1998-2000)
Ford: Galaxy |
 |
| |
|
Module 24 -
VW, Seat, Ford IMMO3 immobox Valeo
Memory device is serial eeprom 24c04 SMD8 package.
Expected file size is 512
bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready programmed to start
the vehicle.
Vehicles equipped with this unit:
VW: Lupo(2000-2002), Polo(2000-2002), Transporter(2000-2002)
Seat: Arosa(2000-2002), Alhambra(2000-2002), Inca(2000-2002)
Ford: Galaxy(2000-2002) |
 |
| |
|
Module 26 - Renault immobox
Siemens
Memory device is Motorola MCU MC68HC05B16 PLCC52 package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Renault: Megane(-1999), Twingo(-2000) |
 |
| |
|
Module 27 - Renault immobox
Valeo
Memory device is serial memory 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Renault: Laguna(-2001), Safrane, Espace(-1998) |
 |
| |
|
Module 28 - Renault,Dacia
immobox Sagem
Memory device is serial memory 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Module also shows 4-digit PIN code.
Vehicles equipped with this unit:
Renault: Kangoo(-2001), Clio(-2001), Trafic(-2001), Master(-2001)
Opel: Movano(-2001)
Dacia: Supernova |
 |
| |
|
Module 29 - Renault BSI
Valeo
Memory device is Motorola MCU MC68HC908AZ32 QFP64 package.
Expected file size is 512 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Renault: Espace(1998-2002) |
 |
| |
|
Module 30 - Renault UCH
Sagem
This module can be used in 2 ways:
1.If you don`t know 12-digit PIN code:
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Module calculates PIN code.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder have to be matched with car using diagnostic device.
2.If you know 12-digit PIN code:
Start software and select module.
Insert PCF7936 or Silca T14 - JMA TP12 transponder.
Press PROG button. Software opens box,
where you must enter 12-digit PIN code.
Verify it and press OK.
Match prepared transponder with car
using diagnostic device and PIN
code.
Vehicles equipped with this unit:
Renault: Clio(2001-2006) |
 |
| |
|
Module 31 - Renault UCH
Siemens
This module can be used in 2 ways:
1.If you don`t know 12-digit PIN code:
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Module calculates PIN code.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder have to be matched with car
using diagnostic device.
2.If you know 12-digit PIN code:
Start software and select module.
Insert PCF7936 or Silca T14 - JMA TP12 transponder.
Press PROG button. Software prepares transponder.
Match prepared transponder with car using
diagnostic device and PIN code.
Vehicles equipped with this unit:
Renault: Clio Symbol(2001-2006)
Dacia: Logan, Logan MPV |
 |
| |
|
Module 32 - Mercedes Sprinter,
Vito immobox Temic
Memory device is Motorola MCU, which can be either
MC68HC05X16 or MC68HC908AZ32, both QFP64 package.
For MC68HC05X16 expected file size is 256 bytes,
for MC68HC908AZ32 expected file size is 512 or 1024 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Note: if immobox contain RF receiver in metal box,
this means that original key had remote function.
In this case you have also to perform START ERROR repair.
Important note: if Motorola MCU is MC68HC05X16 - eeprom area is locked, you have to use proper programmer to read it.
Vehicles equipped with this unit:
Mercedes: Sprinter(1998-2006), Vito(1998-2006)
VW: LT28(2000-), LT35(2000-) |
 |
| |
|
Module 34 - Volvo IMMO3 immobox
Bosch
Memory device is serial eeprom 93c56 or 93c66, both SMD8 package.
For 93c56
expected file size is 256 bytes, for 93c66 is 512 bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Volvo: C70(1998-), S40(1998-), S70(1998-), S80(1998-1999), V40(1998-), V70(1998-2000)
Volvo trucks: FH12 |
 |
| |
|
Module 35 - Volvo, Mitsubishi CARTRONIC immobox Bosch
Memory device is serial memory 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Mitsubishi: Carisma, Magna
Volvo: 850, 940, 960, C70(-1998), Polar, S40(-1998), S70(-1998), V40(-1998), V70(-1998) |
 |
| |
|
Module 36 - Iveco Daily/Iveco
Truck immobox Bosch
This module can be used in 2 ways:
1.If you don`t know 5-digit PIN code:
Memory device is serial eeprom 93c56 SMD8 package.
Expected file size is 256 bytes.
Module calculates PIN code.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder have to be matched
with car using diagnostic device.
2.If you know 5-digit PIN code:
Start software and select module.
Insert PCF7936 or Silca T14 - JMA TP12 transponder.
Press PROG button. Software prepares transponder.
Match prepared transponder with car
using
diagnostic device and PIN code.
Vehicles equipped with this unit:
Iveco: Daily(2001-2007)
Iveco trucks: Eurocargo(2001-2007), Stralis(2001-2007) |
 |
| |
|
Module 37 - Mercedes Actros,
Atego engine ECU Temic
Memory device is serial eeprom, which can be
93c56, 93c66 or 93c86, all SMD8 package.
For 93c56 expected file size is 256 bytes,
for 93c66 expected file size is
512 bytes and for 93c86 is 2048 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Mercedes: Actors(1998-2006), Atego(1998-2006) |
 |
| |
|
Module 38 -
Opel, Isuzu immobox Megamos
Memory device is serial eeprom 93c46 SMD8 package.
Expected file size is 128 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Module also shows PIN code and
transponder
have to be matched with car.
Vehicles equipped with this unit:
Opel: Frontera(1998-) |
 |
| |
|
Module 39 -
PSA VAG Opel Nissan Ford Mitsubishi new chip
This module can prepare PCF7935 or Silca T15 - JMA TP14
transponders,so they become ready to be matched
with particular car using diagnostic device and PIN code.
Module is useful when you have amount of blank PCF7935
or VAG ID44 transponders.
When you got car, which uses ID40, ID41, ID42, ID44 or ID45
and you have PIN code just prepare PCF7935
using this module and after that match transponder
with car using diagnostic device.
Prepared ID40 chips are switable
for absolutely all Opel Immo1/Immo2 cars.
Prepared ID41 chips are switable
for Nissan NATS 2-4 and some NATS 5 cars.
Prepared ID42/ID44 VAG chips are switable
for absolutely all VAG Immo1/Immo2 cars with external immoboxes
and also for Ford Galaxy.
Prepared ID45 chips are switable for all Peugeot 206/406 with BSI Siemens. |
 |
| |
|
Module 40 - BMW, Rover, Mini
immobox EWS
Memory device is Motorola MCU MC68HC11EA9 PLCC52
or MC68HC9S12D64 QFP80 package.
IMPORTANT NOTE: Motorola MC68HC9S12D64 IS LOCKED.
If you try to read it thru BDM you will erase
it.
For Motorola MCU MC68HC11EA9 PLCC52 package
expected file size is 512 bytes,
for
MC68HC9S12D64
QFP80 package expected file size is 1024 bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready to start car.
Software always program first unused key.
After programming of transponder, software asks you
if to memorise key number or not.
In case you select yes, software stores in PC registry key
number along with file information,
so on next press of PROG button to be programmed next unused
key.
Also this is useful, if same customer came back
for second key or if again all keys are lost
- you do not need to remove and read again EWS eeprom.
Just open customer`s file and software
automatically will position on next unprogrammed key,
cause it finds in registry which key was
programmed in previous.
Vehicles equipped with this unit:
BMW: series 3(-2002), series 5(-2002), series 7(-2002), series 8(-2002),
X-3(-2002), X-5(-2002), M3(-2002),
Z3(-2002)
Rover: 75
Mini: Cooper |
 |
| |
|
Module 41 - Mazda immobox
Temic
Memory device is Motorola MCU MC68HC705P3 SO28 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Mazda: 323(-1999), 626(-1999), MX-3, MX-5, MX-6, Xedox 6, Xedox 9
Ford: Probe |
 |
| |
|
Module 42 -
Mazda immobox Lucas 19AS
Memory device is Motorola MCU MC68HC05B6 PLCC52 package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Mazda: 323(-1999), 626(-1999), MX-5 |
 |
| |
|
Module 43 -
Nissan, Subaru immobox Siemens
Memory device is Motorola MCU MC68HC05B6 PLCC52 package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Nissan: Primera(-1998), Pulsar(-1998), Serena(-1998), Sunny, Terrano 2(-1998), Vannete(-1998)
Subaru: Impreza(-2000), Legacy(-1998), Outback(-1998) |
 |
| |
|
Module 44 -
Renault UCH Sagem type 2
This module can be used in 2 ways:
1.If you don`t know 12-digit PIN code:
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Module calculates PIN code.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder have to be matched with car using diagnostic device.
2.If you know 12-digit PIN code:
Start software and select module.
Insert PCF7936 or Silca T14 - JMA TP12 transponder.
Press PROG button. Software opens box,
where you must enter 12-digit PIN code.
Verify it and press OK.
Match prepared transponder with car
using diagnostic device and PIN code.
Vehicles equipped with this unit:
Renault: Kangoo(2002-2007), Twingo(2002-2007), Trafic(2002-2007), Master(2002-2007)
Opel: Vivaro(2002-2007), Movano(2002-2007)
Nissan: Interstar(2002-2007) |
 |
| |
|
Module 45 -
Fiat, Lancia, Citroen, Peugeot vans, Iveco vans/trucks CODE2 with BSI Marelli type 2
Memory device is serial eeprom 95c160 or 95c320, both SSOP8 package.
For 95c160 expected file size is 2048 bytes, for 95c320 is 4096 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Module also shows PIN code and
transponder
have to be matched with car.
Vehicles equipped with this unit:
Fiat: Bravo(2007-), Ducato(2006-), Stilo(2007-), Punto(2007-)
Citroen: Jumper(2006-), Relay(2006-)
Peugeot: Boxer(2006-)
Lancia: Ypsilon(2007-)
Iveco: Daily(2007-), Eurocargo(2007-) |
 |
| |
|
Module 46 -
Volvo IMMO1 immobox Bosch
Memory device is serial memory 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Volvo: 850, 940, 960, C70(-1998), Polar, S40(-1998), S70(-1998), V40(-1998), V70(-1998) |
 |
| |
|
Module 47 -
Saab body module TWICE
Memory device is Motorola MC68HC05X32 QFP64 package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the
vehicle.
Important note: Motorola MCU is with locked eeprom area, you have to use proper programmer to read it.
Vehicles equipped with this unit:
Saab: 9-3(-2003), 9-5(-2003) |
 |
| |
|
Module 48 -
Fiat New Panda BSI Siemens VDO
Memory device is Motorola MCU MC9S12DG128 QFP 112 package.
Expected file size is 2048 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Module also shows PIN code and
transponder have to be matched with car.
If there is not valid key, usual you have to wait
15 minutes for accepting PIN code.
Vehicles equipped with this unit:
Fiat: Panda(2003-) |
 |
| |
|
Module 49 -
Opel, Isuzu immobox Megamos type 2
Memory device is serial eeprom 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Opel: Frontera(1996-1998) |
 |
| |
|
Module 50 -
Jaguar immobox
Memory device is serial eeprom 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Jaguar: Sovereign, XJ, XJS, XK, XK8 |
 |
| |
|
Module 51 -
Renault Premium/Midlum immobox Texton
Memory device is serial eeprom 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Renault: Premium(-2007), Midlum(-2007) |
 |
| |
|
Module 52 -
Toyota immobox with ID33
Memory device is serial eeprom 24c04 DIL8 package.
Expected file size is 512 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Toyota: Carina, Celica(-1998), Estima(-1998), Paseo(-1998), Previa(-1998), Starlet(-1998) |
 |
| |
|
Module 53 -
MAN TGA module FFR
Memory device is serial eeprom, which can be either 25c128 or 25c256, both
SMD8 package.
Expected file size is 16384 or 32768 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Man: TGA trucks |
 |
| |
|
Module 54 - Porsche body module with
ID13
Memory device is serial eeprom 93c56 SMD8 package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Porsche: 911(-1999), Boxter(-1999) |
 |
| |
|
Module 55 - General Motors Passkey3
immobox Delphi
Memory device is Motorola MCU MC68HC908AS20 PLCC52 package.
Expected file size is 512 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Buick: Century, Le Sabre, Park Avenue, Regal, Rendevouz, Roadmaster
Cadillac: Deville STS, Dorado, S5S, Seville, STS
Chevrolet: Camaro, Cavalier, Corvett, Impala, Malibu, Montecarlo, Venture
Oldsmobile: Aurora, Silhouette
Pontiac: Aztec, Bonneville, Grand Prix, Montana |
 |
| |
|
Module 56 - Acura immobox
Memory device is serial eeprom 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Acura: 3.5 RL, CL, Integra, MD-X, NSX, TL |
 |
| |
|
Module 57 - Renault UCH Johnson Controls type 1
This module can be used in 2 ways:
1. If you don`t know 12-digit PIN code:
Memory device is serial eeprom 95c080 SMD8 package.
Expected file size is 1024 bytes.
Module calculates PIN code.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder have to be matched with car using diagnostic device.
2. If you know 12-digit PIN code:
Start software and select module.
Insert PCF7936 or Silca T14 - JMA TP12 transponder.
Press PROG button. Software opens box,
where you must enter 12-digit PIN code.
Verify it and press OK.
Match prepared transponder with car
using diagnostic device and PIN code.
Vehicles equipped with this unit:
Renault: Kangoo(2007-), Trafic(2007-), Master(2007-)
Opel: Vivaro(2007-), Movano(2007-) |
 |
| |
|
Module 59 - Fiat Grande Punto BSI
Delphi
Memory device is serial eeprom 93c86 SMD8 package.
Expected file size is 2048 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder
or remote key with PCF7946.
Module also shows PIN code and transponder has to be matched with car.
Vehicles equipped with this unit:
Fiat: Grande Punto, New 500, Fiorino
Alfa Romeo: Mito
Ford: KA
Citroen: Nemo
Peugeot: Beeper |
 |
| |
|
Module 60 - Polonez immobox
Megamos
Memory device is serial eeprom 93c46 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Polonez: Pick-up |
 |
| |
|
Module 61 - Tata Safari immobox Alltech
Memory device is serial eeprom 24c01 SMD8 package.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Tata: Safari |
 |
| |
|
Module 62 - Key copier for ID11, ID12,
ID13, SAAB and ID33 fixed keys onto T5 transponder
Module helps you to copy Philips, Temic and Megamos fixed keys onto T5 transponder.
For Renault ID33 key you can see 4-digit PIN code. |
 |
| |
|
Module 63 - Key copier for ID33,
ID41, ID42, ID44 VAG and ID45 keys onto PCF7935 transponder
Module helps you to copy crypto keys onto PCF7935 transponder.
For ID45 Peugeot 206/406 keys module shows vehicle PIN code. |
 |
| |
|
Module 64 - Key copier for 4C
Texas fixed keys onto JMA TPX1 transponder
Module helps you to copy Texas fixed keys onto JMA TPX1 - Errebi TX1 transponder. |
 |
| |
|
Module 65 - Key copier for 4D
Texas crypto keys onto JMA TPX2 transponder
Module helps you to copy Texas fixed keys onto JMA TPX2 - Errebi TX2 transponder.
For Renault ID4D keys it shows 8-digit PIN code.
IMPORTANT NOTE: you need JMA TPX Clonner for to copy Texas Crypto keys/read Renault 8-digit PIN code from
key.
Cloner need to be connected to your PC COM port.
If your PC don`t have COM port,
you can use good USB-RS232 converter
or PCMCIA-RS232 card.
Cloner also need 12 v supply to work.
Click here to see how to make simple convertor cable for to connect cloner to PC COM
port. |
 |
| |
|
Module 69 - Mazda 3 dashboard YNS
Memory device is serial eeprom 93c56 or 93c66 8 pin SMD package.
Expected file size for 93c56 is 256 bytes and for 93c66 is 512 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Mazda: 3, 5, 6(2009-), CX-7, CX-9 |
 |
| |
|
Module 70 - Ford Focus dashboard
Visteon
Memory device is MC9S12H256 112 pin QFP package.
Expected file size is 4096 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Ford: Focus, C-Max, Transit Connect, Fiesta(2009-) |
 |
| |
|
Module 71 - Jaguar dashboard
Memory device is HC912DG60/DG128 112 pin QFP package.
Expected file size is 1024/2048 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Jaguar: X-type |
 |
| |
|
Module 72 - Ford engine ECU Delphi
Memory device is serial eeprom 95c160 8 pin SMD package.
Expected file size is 2048 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Ford: Focus, Fusion, Mondeo, Transit |
 |
| |
|
Module 73 - Ford engine ECU
Visteon
Memory device is serial eeprom 95c040 8 pin SMD package.
Expected file size is 512 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Ford: Focus, Fusion, Mondeo, Transit |
 |
| |
|
Module 74 - Ford,Mazda engine ECU
Siemens
Memory device is serial eeprom 93c56/93c86 8 pin SMD package.
Expected file size is 256/2048 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Ford: Fiesta
Mazda: Mazda2 |
 |
| |
|
Module 75 - Ford Galaxy immobox
Memory device is serial eeprom 24c02 8 pin SMD package.
Expected file size is 256 bytes.
Use T5 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Ford: Galaxy |
 |
| |
|
Module 76 - Chrysler immobox SKIM
Memory device is serial eeprom 24c02 8 pin SMD or Motorola HC908AB16
or Motorola HC908AZ32 64 pin QFP package.
Expected file size is 256 or 512 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Chrysler, Jeep, Dodge |
 |
| |
|
Module 77 - KIA immobox Shinchang
Memory device is serial eeprom 93c46 8 pin SMD package.
Expected file size is 128 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Kia: Carens, Clarence, Joice, Rio, Sportage |
 |
| |
|
Module 78 - Suzuki immobox
Mitsubishi
Memory device is serial eeprom 24c01 8 pin SMD package.
Expected file size is 128 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Suzuki: Alto, Ignis, Jimny |
 |
| |
|
Module 79 - Renault Megane immobox
Siemens
Memory device is Motorola MC68HC05B6 52 pin PLCC package.
Expected file size is 256 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Module also shows PIN code if you wish to program
common Texas crypto chips with diagnostic device.
Vehicles equipped with this unit:
Renault: Megane, Scenic |
 |
| |
|
Module 80 - Renault Megane UCH
Siemens
Memory device is Motorola MC68HC705B32 52 pin PLCC package.
Expected file size is 256 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Module also shows PIN code if you wish to program
common Texas crypto chips with diagnostic device.
Vehicles equipped with this unit:
Renault: Megane, Scenic |
 |
| |
|
Module 81 - Mazda 6 engine ECU
Denso
Memory device is serial eeprom 93c56 SMD 8 package.
Expected file size is 256 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Mazda: 6 |
 |
| |
|
Module 82 - Mazda 6 engine ECU
Mitsubishi
Memory device is serial eeprom 24c02 SMD 8 package.
Expected file size is 256 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Mazda: 6 |
 |
| |
|
Module 83 - Toyota Avensis immobox
Valeo with ID4D-60
Memory device is Motorola MCU MC68HC05E6 SO28 package.
Expected file size is 160 bytes.
Use TPX2 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Toyota: Avensis, Corolla |
 |
| |
|
Module 84 - Ford Transit 2008 BCM Siemens
VDO
Memory device is Motorola MCU MC9S12DT256 QFP 112 package.
Expected file size is 4096 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Ford: Transit 2008 |
 |
| |
|
Module 85 - SsangYong immobox VDO
Memory device is Motorola MCU MC68HC05B16 SDIP56 package.
Expected file size is 256 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
SsangYong: Musso, Korando, Rexton (2002 - 2006) |
 |
| |
|
Module 86 - Chery, Samand immobox Siemens VDO
Memory device is Motorola MCU MC68HC908AB16A QFP64 package.
Expected file size is 256 or 512 bytes.
Use PCF7935 or Silca T15 - JMA TP14 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Chery: Asprinza, Speranza, Shrman
Samand: Soren |
 |
| |
|
Module 87 - Toyota, Lexus ECU Bosch, Fujitsu, Denso
Memory device is serial eeprom, which can be
25020/25080/93c56/93c86, all 8
pin SMD package.
Expected file size for 25020 and 93c56 is 256 bytes,
for 25080 is 1024
bytes and for 93c86 is 2048 bytes.
Use JMA TPX1 - Errebi TX1 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Toyota: RAV4, Corolla, Sienna, Yaris
Lexus: IS200, IS300, GS300 |
 |
| |
|
Module 88 - Scania truck module Coordinator
Memory device is serial eeprom Xicor X5328 8 pin SMD package,
which is equal to SPI serial eeprom 95c320, or serial eeprom 25c256.
For X5328 expected file size is 4096 bytes,
for 25c256 expected file size is 32768 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start truck.
Vehicles equipped with this unit:
Scania: P230, P270, P280, P310, P320, P340, P360, P380, P400, P420
R340, R360, R380, R400, R420, R440, R470, R480, R500, R560, R580, R620 |
 |
| |
|
Module 89 - Mazda RX-8 immobox Visteon
Memory device is serial eeprom 24c02 SMD 8 package.
Expected file size is 256 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Mazda: RX-8 |
 |
| |
|
Module 91 - Opel, Isuzu immobox
Tokai-Rika with ID4D-64
Memory device is serial eeprom 93c66 DIL8 package.
Expected file size is 512 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Opel: Monterey
Isuzu: Big Horn, Trooper |
 |
| |
|
Module 92 - Toyota, Suzuki, Daihatsu
immobox with ID4C
Memory device is serial eeprom 93c66 DIL8 package.
Expected file size is 512 bytes.
Use JMA TPX1 - Errebi TX1 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Toyota: 4-Runner(1997-2003), Avalon(1997-2003), Camry, Celsior,
Colorada, Corolla(1996-2002), Echo, Hiace, Highlander(2001-2003),
Hilux(1999-2004), Duet
Suzuki: Alto(1996-2002), Baleno, Grand Vitara(1996-2002), Jimny(1999-2002), Swift(1996-2005), Vitara(1996-2002),
WagonR(1998-2000)
Daihatsu: Charade, Copen, Cuore, Feroza, Move, Sirion(1998-2004), Terios(1997-2005), YRV
Isuzu: Trooper |
 |
| |
|
Module 93 - DAF trucks immobox VDO
Memory device is Motorola MCU MC68HC908AZ32 QFP64 package.
Expected file size is 512 bytes or 1024.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
DAF: CF, LF, XF series |
 |
| |
|
Module 94 - Renault, Nissan UCH Johnson
Controls type 2
Memory device is serial eeprom 95c080 or 95c160 SMD8 package.
Expected file size is 1024 or 2048 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder or remote key.
IMPORTANT NOTE: Nissan Micra K12 accepts ONLY REMOTES.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Renault: Clio3, Modus
Nissan: Micra k12 |
 |
| |
|
Module 95 - Chrysler, Jeep immobox
DaimlerChrysler
Memory device is serial eeprom 95c040/95c080/24c16 SMD8 or SSOP8 package or Motorola 912DG128 112 pins QFP.
Expected file size is 512 or 1024 or 2048 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Jeep: Compass, Commander, Grand Cherokee(2005-), Liberty(2005-), Patriot, Wrangler(2007-)
Chrysler: 300C(2005-), Pacifica(2004-), Voyager(2005-), Aspen (2007-), PT Cruiser(2006-), Sebring(2007-) |
 |
| |
|
Module 99 - Mitsubishi, Suzuki immobox
ID4C type 2
Memory device is serial eeprom 24c01 SMD8 package.
Expected file size is 128 bytes.
Use JMA TPX1 - Errebi TX1 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Mitsubishi: 3000GT, Colt, Eclipse, Express, Galant, Lancer, Mirage, Montero, Nimbus, Pajero,
Shogun, Space Gear, Space Runner,
Space Wagon
Suzuki: Alto, Grand Vitara, Baleno, Jimny, Swift, Vitara |
 |
| |
|
Module 100 - Fiat dashboard
Marelli, VDO
Memory device is serial eeprom 95c160 or 24c16 both SMD8 package.
Expected file size is 2048 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Module also shows PIN code and transponder
has to be matched with car.
Vehicles equipped with this unit:
Fiat: Palio, Siena, Strada, Uno 2010 |
 |
| |
|
Module 102 - Samand, Saipa, Chery,
Hainan Mazda new chip
This module can prepare PCF7935 or Silca T15 - JMA TP14 transponders,
so they become ready to be matched with particular car
using diagnostic device and PIN code.
There are 3 types supported: Samand/Saipa, Chery and Hainan Mazda.
If you are not sure about key type of your car,
read original key and check last 3 bytes on screen.
Then at select menu of module choose same type. |
 |
| |
|
Module 103 - Texas Crypto new chip
This module can prepare Texas Crypto or Silca 4D-60 - JMA TP06/TP19 transponders,
so they become ready to be matched with particular car
using diagnostic device and PIN code.
You can change Texas Crypto chips to 9 different types:
Mitsubishi 4D-61, Subaru 4D-62, Ford/Mazda 4D-63, Suzuki 4D-65,
Suzuki 4D-66, Suzuki bike, Yamaha bike, Kawasaki bike master key,
Kawasaki bike slave key.
Note: this module uses common glass or ceramic Texas crypto chips, not JMA TPX2 chips. |
 |
| |
|
Module 104 - Honda, Acura immobox
Valeo ID46
Memory device is serial eeprom 24c04 or 93c66 both SMD8 package.
Expected file size is 512 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Honda: Accord, Civic, CR-V, Element, Pilot, Ridgeline
Acura: CSX, MDX, RDX, TL, TSX |
 |
| |
|
Module 105 - Honda immobox HIS-5 ID48
Memory device is serial eeprom 93c46 SMD8 package.
Expected file size is 128 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Honda: Accord, Civic, CR-V, FR-V, HR-V, Insight, Jazz, Logo, S 2000, Shuttle, Stream |
 |
| |
|
Module 106 - Mazda 6 diesel ECU Denso
Memory device is serial eeprom 93c86 SMD8 package.
Expected file size is 2048 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Mazda: 6 |
 |
| |
|
Module 107 - Hyundai, Kia engine ECU
Kefico, Bosch
Memory device is serial eeprom 95c040 or 95c160 or 95p08, all SMD8 package.
For 95c040 expected file size is 512 bytes, for 95c160 expected file size is 2048 bytes, for 95p08 expected file size is 1024
bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder..
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Hyundai: Atos, Atos Prime, Getz, Accent, Coupe
Kia: Sorento, Carens, Picanto, Santa Fe, Ceed |
 |
| |
|
Module 110 - Smart ForFour ETACS
Siemens-VDO
Memory device is Motorola MCU MC9S12B128 QFP112 package.
Expected file size is 2048 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder or remote key.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Smart: ForFour
Mitsubishi: Colt IV |
 |
| |
|
Module 111 - Saab
column module CIM
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder or remote key.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Saab: 9-3(2003-), 9-5(2003-)
Cadillac: BLS |
 |
| |
|
Module 112 -
Fiat, Lancia, PSA BSI Marelli type 3
Memory device is serial eeprom 95c160 SSOP8 package.
Expected file size is 2048 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder or remote key.
Module also shows PIN code and transponder has to be matched with car.
Vehicles equipped with this unit:
Fiat: Bravo(2007-), Ducato(2006-), Stilo(2007-), Punto(2007-)
Citroen: Jumper(2006-), Relay(2006-)
Peugeot: Boxer(2006-)
Lancia: Ypsilon(2007-), Musa(2007-) |
 |
| |
|
Module 113 -
Daewoo, Chevrolet immobox ID48
Memory device is serial eeprom 93c56 SMD8 package.
Expected file size is 256 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Chevrolet: Aveo, Kalos, Lacetti, Leganca, Matiz, Nubira, Takuma |
 |
| |
|
Module 114 -
Mitsubishi immobox ID46
Memory device is serial eeprom 24c01 SMD8 package.
Expected file size is 128 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Mitsubishi: Lancer, Pajero |
 |
| |
|
Module 115 -
Chevrolet BSI Siemens
Memory device is Motorola MC68HC705B32 52 pin PLCC package.
Expected file size is 256 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Chevrolet: Epica, Evanda |
 |
| |
|
Module 116 -
Isuzu immobox SiemensVDO
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Isuzu: Elf, D-MAX, MU-7 |
 |
| |
|
Module 117 -
Chevrolet, Opel immobox ID46
Memory device is serial eeprom 95c040 SMD8 package.
Expected file size is 512 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Chevrolet: Captiva, HHR, Cobalt
Daewoo: Windstorm
Opel: Antara
GMC: Siera |
 |
| |
|
Module 118 -
Alfa Romeo, Fiat BSI Marelli type 4 with ID46
Memory device is Motorola MCU MC9S12DG256 QFP112 package.
Expected file size is 4096 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder or remote key.
Module also shows PIN code and transponder has to be matched with car.
Vehicles equipped with this unit:
Alfa Romeo: 159
Fiat: Croma |
|
| |
|
Module 130 - BMW, Mini
CAS SiemensVDO
Memory device is Motorola MCU 912DG256 or 9S12DG256.
Expected file size is 2048 or 4096 bytes.
IMPORTANT NOTE: Motorola MCU is locked,
please use proper programmer.
Use PCF7936 or PCF7942 - PCF7943 - PCF7945 transponder or remote key.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
BMW: series 1, series 3, series 5, X-3, X-5
Mini: Cooper |
 |
| |
|
Module 132 - Nissan
Sunny dashboard
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Nissan: Sunny (2007-) |
 |
| |
|
Module 133 - Citroen
Xantia CPH Texton ID48
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Citroen: Xantia (1998-) |
 |
| |
|
Module 134 - Renault
Twingo 2 UCH Temic
Memory device is Motorola MC9S12B256 QFP112 package.
Expected file size is 4096 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder or remote key or card.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Renault: Twingo 2 (2007-) |
 |
| |
|
Module 135 - Subaru
immobox Mitsubishi
Memory device is serial eeprom 24c01 SMD8 package.
Expected file size is 128 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Subaru: Tribeca(2005-), Forester(2005-), Outback(2005-), Legacy(2005-) |
 |
| |
|
Module 136 - Ford
BSI Delphi
Memory device is serial eeprom 95c320 8 pin SMD package.
Expected file size is 4096 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Ford: Mondeo, S-MAX |
 |
| |
|
Module 137 - GM
Passkey3+ immobox Delphi ID48
Memory device is Motorola MCU MC68HC908AZ32 QFP64 package.
Expected file size is 512 bytes or 1024.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Cadillac: BLS
Chevrolet: Blazer |
 |
| |
|
Module 138 - GM
Passkey immobox ID46
Memory device is Motorola MCU MC9S12B128 QFP112 package.
Expected file size is 2048 bytes.
Use PCF7936 or Silca T14 - JMA TP12 transponder or remote key.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
Chevrolet: Malibu
Pontiac: G5, G6, Solstice, Pursuit |
 |
| |
|
Module 139 -
SsangYong, Proton engine ECU VDO
Memory device is flash AMD AM29F200BB 44 pin SSOP package.
Expected file size is 262144 bytes.
Use Megamos Crypto or Silca T6 - JMA TP08 transponder.
Written transponder is ready programmed to start car.
Vehicles equipped with this unit:
SsangYong: Actyon
Proton: Wira |
 |
| |
|
Module 140 - KIA
immobox Texton ID13
Memory device is Motorola MCU MC68HC805P18 SO28 package.
For reading this MCU you can use Motorola MC68HC805P18 adapter.
Expected file size is 128 bytes.
Use T5 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Kia: Clarus, Shuma, Sportage |
 |
| |
|
Module 141 - Suzuki
Liana immobox
Memory device is serial eeprom 93c66 SMD8 package.
Expected file size is 512 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Suzuki: Liana |
 |
| |
|
Module 142 - Ford
engine ECU Siemens, EEC5 with ID4C
Memory device is serial eeprom 93c86 or 95c040 both SMD8 packages.
For 93c86 expected file size is 2048 bytes and for 95c040 file size is 512 bytes.
Use JMA TPX1 - Errebi TX1 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Ford: KA, Fiesta, Mondeo |
 |
| |
|
Module 143 -
Mitsubishi, Subaru immobox Mitsubishi ID4D
Memory device is Motorola MCU MC68HC805P18 QFP44 package.
For reading this MCU you can use Motorola MC68HC805P18 adapter.
Expected file size is 128 bytes.
Use JMA TPX2 - Errebi TX2 transponder.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Mitsubishi: Eclipse, Galant, Lancer, Pajero, Montero, Shogun
Subaru: Tribeca, Forester, Impreza, Legacy |
 |
| |
|
Module 144 -
Renault UCH Johnson Controls type 3
Memory device is serial eeprom 95c160 SMD8 package.
Expected file size is 2048 bytes.
Use Philips PCF7936 - Silca T14 - JMA TP12 transponder or remote key with PCF7946 - PCF7947.
Written transponder is ready programmed to start the vehicle.
Vehicles equipped with this unit:
Renault: Kangoo (2009-) |
 |
